SUPER-CORE 1850 Watt 12 Volt AC 3 -PH Wind Turbine Permanent Magnet Alternator

Description

MEGA POWER SUPER CORE
This auction is for a  12VAC / 3 Phase / 3  Wire / PMA designed for use with our 34.64" KT propeller (blades)  and with these blades can make up to 1900 Watts peak power in high winds (Rated as peak).
All voltage ranges (VR) are based on use for battery charging with wind power!
This PMA's is recommended for wind turbines only! Peak at about 2000 RPM.
For PMA's / PMG's  for engines / hydro usage please use our line of #PC1212 or #QC1212 models
.
Thermodyne 1600W Wind Turbine Review
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
TREX blades on SC12 PMA Wind Turbine windgeneering
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
What's better, AC or DC wind turbine PMA's / PMG's
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
Thermodnye Hornet Wind Farm
Video will open in a new window
Using the iPhone app? Copy this link into Safari:
See it in action #1
CLICK TO SEE VIDEO
See it in action #2
CLICK TO SEE VIDEO
1850 Watts peak / 2200 RPM at peak load.
For battery charging be sure to buy one of our "battery regulators"
Designed to operate in an area with low/medium speed averages of 4.3 to 5.6 m/s and greater (Zone 3-4)  Provides 256 kWh per month (3072kWh year)  7.4 kWh per day in a 12.6 mph (5.6 m/s) average wind speed.
In a zone 7 area this turbine can make up to 200% more power or 13.75 kWh.
Wind Zones are defined by m/s
Wind Zone 1      0 – 4.4 m/s  (Wind not recommended, go solar in this wind zone)
Wind Zone 2    4.4 – 5.1 m/s
Wind Zone 3    5.1 – 5.6 m/s
Wind Zone 4    5.6 – 6.0 m/s
Wind Zone 5    6.0 – 6.4 m/s
Wind Zone 6    6.4 – 7.0 m/s
Wind Zone 7    7.0 – 9.4 m/s  (20-22 mph)
Make sure your equipment can handle  the peak voltages of each model.
Batteries are good at absorbing high voltages as long as they do not go over
their voltage limits and that is why are battery regulators are critical to match
with our turbines.  We sell many models as long as the voltages match.
Includes a real original  NON-COGGING
SUPER-CORE PMA -
What is cogging?
There are plenty of "Look-A-Like" PMA's on the market that cost less.
The reason why they cost less
is that they are utilizing an old fashioned
The modern type PLATE AND GROOVE rotor that we have developed is the most celebrated and also the most copied type which we pioneered.  The important part is that PLATE AND GROOVE makes power at MUCH LOWER RPM's than the older and traditional Clam type rotor designs that do not provide deep magnetic saturation of the Stator coil offering 600% more power in low RPM scenarios over Clam type designs
In small wind turbines this is VERY important to make your power in the LOWER RPM ranges.
Spend a little more and get a LOT more  BANG-FOR-YOUR-BUCK!!!  Money well spent!
From the beginning GM designed the Delco to run
WET and even tested them to operate
Under Water
!
Designing an alternator that can survive at 375 degrees F. under the hood of a car operating with rain water coming through the
radiator and from water puddles is
No Easy Task!
Over 100,000,000 10/12si's were produced by Delco and after-market vendors!
Parts for this legendary 'work-horse' will be available for the next 50+ years.  World's most supported and well recognized model!
"NOT ALL PMA's ARE CREATED EQUAL"
Our Magnets are on an angle to prevent cogging!
We make our own brand new
ROTOR POLE
SHOES
AND
STATOR CORES
!!!
Our PMA's are built from the ground up using only 100% ALL new parts!
(Including the rotor pole shoes and stator coil stacks)
Our
NEW
rotor poles are balanced to within .002 grams for SMOOOOOTH rotation!